Polaris RZR Plug-n-Play Easy Install TURN SIGNAL & HORN KIT Column Mount Control
Plug & Play UTV Signal Kit
for Polaris RZR
The Dux RZR turn signal/horn kit is easy to install and is 100% plug and play. When installed according to the instructions, all the wires end up in all the right places and everything simply plugs in--the turn switch and turn lights, the horn and horn button,and the flasher. All the wires have labels and are color coded so you can get it right the first time--no special skills needed. Make your RZR safer for road use, fast and easy!
Polaris RZR Product List
- 1xFactory made wiring harness with color coded and labeled wires (USA)
- 4xFull sealed ultra bright LED turn lights with bullet ends
- 1x105db motorcycle horn
- 1xColumn mounted turn switch with indicator lights built in and 4-way hazard feature
- 1xHorn button with rubber boot
- 1xLED flasher
- 10xWire ties
- Made in the USA
Thread the wiring harness through the chassis starting from under the dash. There is an opening in the firewall that the factory wiring runs through. The front half will do down the left side, then across the front of the radiator to the right front corner. Removing the hood will make it easier. The rear half will follow the factory harness. It will be much easier if you loosen or remove the skid plate.
Mounting the Horn,Turn Switch, Horn Button and Indicator Light
A good place for the horn is above the LF tire between the headlight housing and the radiator. Mount it horizontally with the spade terminals facing up.
The horn button will go on the flat area to the right of the steering column. Drill a 15/32" hole to mount it.
Attach the turn signal switch to the steering column. The switch must be grounded, so a ground wire is provided with a #8 ring that can be slipped under the strap or under the screw that tightens the strap.
Connect the switches, flasher and horn
Connect the red and black wires to the horn. Connect the two black wires to the horn button. The orange and brown wires MUST go to the + side of the flasher, the red wire goes to the L (load) side.
On the turn switch, the blue wire goes to the "P" spade on the flasher. The yellow wire goes to the red wire on the harness, the green wire goes to the yellow wire, the the red wire goes to the green wire.
Note: The harness maker and the switch maker use different color codes.
Mounting the Turn Lights
To mount the Maxxima mini LED lights you will need to drill a 3/4" hole in the body for each light. A sharp wood boring bit or a hole saw will work. The location may vary depending on if you have bumpers. After selecting the location and drilling the hole, install the black grommet into the hole, thread the wires through the grommet, then push the light into the grommet.
Note: the word "top" on the light lens. The black wire on the light will connect to either the green or yellow wire on the wiring harness and the white wire on the light will connect to the black wire on the wiring harness. The brown wire on the wiring harness is for a license plate light where needed. If it is not used, tape over the end.
The power will come from the back side of the accessory socket. Unplug both wires and connect them to the harness matching orange to orange and brown to black. Now connect the harness wires to the accessory socket: orange to the center and black to the outside. With the key on, test the horn and lights.
Note: Always carry a spare 3-amp fuse.
Limited Warranty Statement
DUX Signal Kits LLC warrants that the product you have purchased is free from defects in materials and workmanship under normal use for a period of 90 days from date of purchase. During the warranty period, DUX Signal Kits LLC will replace defective parts with new parts. In no event shall DUX Signal Kits LLC be liable for any loss, inconvenience, or damage resulting from breach of this warranty.
Limitations of Warranty
The warranty does not apply to the following:
Damage to the product caused by
- improper installation
- crash, impact, or abuse of the product
- water entering electrical components
Except as expressly set forth in this warranty, DUX Signal Kits LLC makes no other warranties expressed or implied. DUX Signal Kits LLC expressly disclaims all warranties not stated in this limited warranty. Any implied warranties that may be imposed by law are limited to the terms of this express limited warranty.